Poly-Flow Engineering wird vertreten^* von
Crystec Technology Trading GmbH

        OMNICLEAN

• Vertical furnace tubes up to 16 3/4” in diameter can be cleaned.
• Oversize carousel is equipped with specialized fixturing to handle boats, T/Cs and pedestals.
• Meets the stringent H6 building code by storing less than 25 gallons of acid for a dual chemical cycle.
• Available with fire safe construction featuring Corzan 4910 exterior.
• 200mm and 300mm configurations available.

        TYPHOON

• Dual oversize carousels are capable of handling a wide range of parts.
• A tube or liner plus various items on each side.
• Each side operates with simultaneous and independent recipes with isolated process systems.
• Four tanks included to provide a recirculating and a single use polish acid for each side.
• 200mm and 300mm configurations available.

        TYPHOON SC

• Now an even more affordable all spray system is available.
• Huge savings over immersion cleaning.
• Greatly reduce acids on board.
• Small footprint.
• Fast cycle.
• Proven Typhoon cleaning process.
• Advanced safety.

        DOUBLE/DOUBLE

• Dual chamber system precision cleans quartzware behind a single front door.
• Each system has separate tube and parts chambers or twin tube chambers with custom fixturing.
• Right chamber handles tubes 48” to 120” long.
• Left chamber has 360° rotating carousel for spray etching of cantilevers, sheaths, boats, paddles, pull rods and assorted parts.

        Triple Tower

• Vertical tube cleaner with three distinctive types of cleaning for all horizontal furnace parts.
• Tubes are consistently etched with the patented Turbo-NozzleTM to clean both inside and outside.
• Paddles, cantilevers, sheaths and master boats rotate on the carousel for 360° etching and rinsing.
• Boats and assorted small parts are immersion etched in the 16” X 12” X 12” sink below the carousel.

        EPITAXIAL BELL JAR CLEANER

• Wide range of soft-touch jaws handle the largest 300mm tubes up to 20 inches.
• Fully counter-balanced design is conservatively rated at 100 lbs. at full height and reach.
• Provides S-8 compliance for Poly-Flow quartzware cleaners.
• 200mm and 300mm configurations available.

        VERTICAL FURNACE QUARTZWARE CLEANER (VFQC)

• Simultaneous cleaning of tubes and liners with dual rotating overhead spray manifolds.
• Dependable immersion cleaning for latest high capacity boats in the largest sink available today.
• Cleaning chamber handles 56” tubes with ease.
• One, two or three acid systems yield process flexibility.
• 200mm and 300mm configurations available.

        HORIZONTAL QUARTZWARE CLEANER

• Features two process chambers.
• Front chamber provides selectable inside/outside etching for furnace tubes up to 86” standard.
• Rear chamber is fixtured for immersion etching of cantilevers, sheaths, boats, paddles, pull rods and other accessories.
• Dual acid configuration with one recirculating and one single use (polish etch).

        AUTOMATIC ACID CLEANING SYSTEM(recirculated chemicals)

• automatic process.
• chemical recirculation from holding tank.
• chemical filtration (selectable)
• multiple BCDS fills to holding tank.

        AUTOMATIC ACID CLEANING SYSTEM(single use chemicals)

• multiple BCDS fills to process sink.
• programmable ratios in process sink.
• variable sink sizes.
• 1 or 2 process sinks.

        AUTOMATIC SOLVENT CLEANING SYSTEM(recirculated chemicals)

• solvent recirculation from holding tank.
• solvent filtration (selectable).
• ultrasonic agitation.
• 1 or 2 solvent holding tanks.

        AUTOMATIC SOLVENT CLEANING SYSTEM(single use chemicals)

• multiple BCDS fills to process sink.
• programmable ratios in process sink.
• ultrasonic agitation.
• variable sink sizes.

        AUTOMATIC ACID AND BASE CLEANING SYSTEM

• multiple BCDS fills each process sink.
• programmable ratios in each process sink.
• 1-5 process sinks.
• simultaneous/independent operation.

        SEMIAUTOMATIC ACID CLEANING SYSTEM

• fill/dump rinsing.
• overflow rinsing.
• programmable rinse times.
• variable sink sizes.

         MIXED CHEMICAL WORK STATION

• solvent sink and acid sink.
• manual rinsing.
• overflow rinsing.
• variable sink sizes.

        MANUAL SOLVENT WORK STATION(solvents)

• timed process.
• variable sink sizes.
• 1 or 2 process sinks.
• AutoFlow II controller.

        MANUAL SOLVENT WORK STATION(corrosives)

• manual rinsing.
• overflow rinsing.
• variable sink sizes.
• multiple process sinks.

        MultiSpec 280 Box & Cassette Cleaner

• Batch cleaning of SMIF Pods, boxes and cassettes.
• No metals in the process stream.
• Vertical design reduces total floor space by 60%.
• Lightly heated HEPA filtered air directed throughout the process chamber to speed drying.

        MultiSpec 277-I

• FOUP & FOSB Cleaner.
• Manual load high through put.
• No high speed rotation.
• Ultra clean process with no metals in the process stream.
• Lightly heated HEPA filtered air directed throughout the process chamber to speed drying.

         MultiSpec 277-II

• The MS-277-II Fully Automated/Factory Integrated system is in the final engineering stages.

• Remove old resist automatically from bottles.
• Recirculated NMP minimizes waste.
• Sloped work deck for ergonomic loading.
• Stainless steel basket for rinsing bottle caps.

• Cleans up to 18 bottles per load.
• Meets EPA regulations.
• Sloped work deck for ergonomic loading.
• Natural polypropylene basket for rinsing bottle caps.

        ACID DRUM CLEANER

• Automatically rinses 55 gallon drums for safe transport and recycling per EPA regulations.
• Optional rinse to programmed pH value.
• Automatic inversion meets ergo requirements and aids drainage.

        VDF QUARTZWARE OVEN

• Increase furnace through put with a pre-diffusion bake of  VDF tubes, boats and accessories.
• Large capacity holds 8 tubes and 8 boats per cycle.
• Twin rotating carousels for easy access to the quartz tube and boats.
• 150°C dry cycle, 190°C desorption cycle, 40°C stand-by

Poly-Flow Engineering, LLC offers benches for processing stents as used by in the cardiovascular industry. The benches are engineered for providing the descaling process and electro-polishing process utilizing a modular approach for bench layout. High tech chemical handing, heating and ultrasonic agitation is standard.

IPA systems are available for sterilization processes for many critical components such as pace makers and insulin injection systems. Aqueous batch processing systems are also available in many configurations for many applications in the medical industry.

Automated delivery systems for acids and bases are available to hold one, two or three drums. Delivery systems are designed to interface with Poly-Flow tools and other manufacturer's tools.